FXWars! RollerCoaster!: Sir_Vulcan

#6

One way to do the banking could be using the loft tool. Create the spline for the path and the shapes for the shape to be extruded along the spline and then after lofting you can edit the “twist” graph under deformations or something like that, so that you can get the shape of the track right.

#7

ya, thats what I ended up doing earlier today, I had tried lofting before but I was doing it backwords. I was picking the shape and lofting it along a line, instead of picking the line and lofting the shape. I think I have it all figured out now. Ill be posting another testing clip soon. Then I think I am ready to make the complete track and work on the visual part.

Thanks for the tip

#8

Ok, here’s an update. On the fourth version of the cars, and I got the loft and banking to work right. http://www.uni-weimar.de/~rehberg/vulcan/CarPhysicsTest04.mov

Time to make the entire track and start adding details.

#9

Nice setup! Seems to work very well!

André

#10

the thing usually doesnt slow donw on loops tho

#11

Ok, here is my track design. I might have to change a few things depending on the physics, but the shape is there. Ill post a picture of the cars soon too, so you can see how they are setup.

So, what do you think?

#12

here’s the car setup I have right now, I was originally planning on four rows of people, but I think the cars might be too long to bend properly around the track. So I might make it into two rows per car, and six cars per train.

#13

Update on the track. It’s a real pain to get this thing to bank right, expecially on the looping parts where the track flips over. I have to go through foot by foot and edit the twist curve. And on the loops the angles on twisting can go from +125 degrees to -154 degrees in just a fraction of an inch. Theres got to be an easier way.:shrug: oh well. it works.

Note: I’ve only gotten to the first corkscrew with the banking.

#14

looks good.

Do you use two curves, one for path and one for twist?

If so… make the second one a clone of the first one and move each
control point a lil bit along the normal of the of the first one as the
start… makes it easier to tweak…

#15

“It’s a real pain to get this thing to bank right”

Yeah, welcome to the club. This is really a pain. The funny thing is when you try to spread the mountings of the main tubes along the track. The “banking” of the tubes was done with the twist curve. For the mountings you use the spline (with the pacing tool). There´s no way to get the twisting information into the spline so the mountings have to be rotated each by each. Or did I miss something?

André

#16

laluneverte: No, I am only using one spline (and then editing the twist curve in the lofts Deformaiton properties) I don’t know how to use another spline for twisting the track. :shrug: I am using max 6, so if you have any suggestion feel free to share them.

ACantarel: lucky for me my track is solid, so I dont have to worry about the supports between the rails. I will have to make the track supports (by hand) but that shouldn’t be hard.

#17

ACantarel: I had the same problem when trying to attach the ties. But it seemed that once I messed with the axis orientation and stuff, it actually did follow the twist using the loft. The screen that is in my topic shows those ties, I made the ties, then used the spacing tool along the original spline, and it actually did bank itself to the loft. It was strange, and I am still trying to figure out how it did that. I can get it to work on like straight hills, but I will try some banked curves in a few hours and see if I can get it work…

One question for Sir_Vuclan though, how do you plan on doing supports?

I haven’t tried it yet, but only ideas I have are to either model every support, or use splines to connect the track and footers, then loft a shape onto those splines… but I would like to hear your input…

#18

I think I am just planning on using splines and lofting the supports or in some cases just make the spline renderable. I haven’t thought about it to much, Working on getting the track built so I can test to make sure the cars make it all the way around. Then after it all works, Ill add everything else.

#19

Ok, new version of…almost everything.

Updated:
Cars (made them shorter to bend around track better)
added more cars
fixed track
tweaked Reactor more

http://www.uni-weimar.de/~rehberg/vulcan/CarPhysicsTest06.mov

Its getting there…

#20

I have the coaster working around most of the track now. This clip doesnt show all of it, but you get the idea. I have a lifting device (box following a spline) to get it up the hill.

I have also started to work on the enviroment around the coaster.

Link to the newest Movie:
http://www.uni-weimar.de/~rehberg/vulcan/CarPhysicsTest07.mov

#21

Ok, I finished my coaster. Now I just have to let it render for about a day. All the physics ended up working great. There are some things I would do differn’t if I have to to this again. But for my first FX-Wars Challenge, I think I did ok.

It may not look the best, spent very little time on the eviroment. But thats not the point, the simulation works. I would like to add more, but not enough time to work on it.:sad:

Final Specs for the coaster:
Length- 1,983’ 11" (604.722m)
Height- 112’ (from lowest point to highest point)
Time- about 1 minute from start to finish

Physics setup:
Used Max6 with Reactor 2. (and one stressed out computer)
Each train car was bound to the track by 6 wheels, Two on top, Two inside, Two on bottom. All the wheels are constrained to their car with wheel constraints. Each car was coupled to the car before it using a point constraint. The lead car uses a hinge constraint to allow it to bend around the track.

Simulation time- about 2 hours for 1550 frames, with 15 sub-steps per frame.

I am planning on rendering it 3 times.

  • On the coaster with enviroment
  • On the coaster with no enviroment(wireframe)
  • Stationary sky cam.

Ill be posting pictures and movies the next few days as I get things rendered, so Check back and LEAVE A COMMENT (whats good or what needs to be fixed), so I can do better next time.

It was a lot of fun and a GREAT learning experience. (I am self-taught, about 2 years worth). Good luck to everyone else :thumbsup:

#22

Looking really good!
I am very impressed! using reactor for that whole thing must have been a super pain!

#23

Twisted Tunnels
Roller Coaster
By
Sir_Vulcan
[left] [/left]

#24

Car setup (What I used with Reactor for simulation) I know the car frame is complicated, but reactor doesnt really care because it used for weight and as a parent for the wheels. I didnt use it for collisions.

#25

Some on board cam shots