Doing 3d Printing? Show us your work...

Become a member of the CGSociety

Connect, Share, and Learn with our Large Growing CG Art Community. It's Free!

REPLY TO THREAD
 
Thread Tools Search this Thread Display Modes
  09 September 2017
Such impressive prints, really digging the smoothness on that print Chewy.

Davidfbarruz, the detail and composition is insane. Great work.

Where is everyone making their 3D prints these days? Is SW still the leader here or are there better low cost alternatives or does everyone have their own printer now?
__________________


Last edited by Junpei : 09 September 2017 at 04:35 PM.
 
  09 September 2017
Originally Posted by Junpei: Where is everyone making their 3D prints these days? Is SW still the leader here or are there better low cost alternatives or does everyone have their own printer now?

I commissioned Factor31 to have my design 3D printed. The service is not cheap, but the turnaround time is fast! Ideally I would want to have my own 3D printer someday. 
__________________
 
  09 September 2017

Here's one of my early attempts at home 3d printing. Not pretty, but I'm getting cleaner prints each time. This is a 4.7"  prop repurposed from my Hit-Girl character model from a bunch of years back. The biggest challenges here were the 0.1mm low res and the stubborn to remove supports. Given that this is on a $220 printer.... not too shabby. Really wish I could find a better way to remove supports or even cleaner, less destructive supports. Cura's killing me with their support structures. Even with pliers, a pen knife, and some sanding, those support areas never seem to come out fully/ :( I could stomach the lower res in exchange for cleaner prints.
__________________
DISCLAIMER: The views presented herein do not necessarily represent those of my brain.
 
  10 October 2017
Here is the mascot I modeled for the upcoming B-Velta, a delta type 3d printer made in France (FDM 3d printer)

Made with ZBrush 4r8 using principally the brushes Move Topology, DamStandard and ClayBuildup.

Thinking to be printed without supports

Then Printed on UM2 with Wood and ngen filament.
Nozzle -> 0.6mm / LayerHeight -> 200µm
Total height : 18cm









 
  10 October 2017
I just finished this 3D printing project, took a lot of time and trial and error but I'm glad it's finally done and I can go back to 3D stuff:
http://forums.cgsociety.org/showthr...f=358&t=1470445
__________________
The Z-Axis
 
  10 October 2017
*Fan Art + 3d Print Mode*
Creation of Asuma Sarutobi's Chakra Blades with a support.
Modelling with Zbrush 4R8.

Blades printed in PlaTec and Support with Easywood Birch from Formfutura. Prints were made with UM2, Nozzle 0.6 mm, Layer of 200µm.
 Painted the blades with tamiya gun metal and Chrome Silver with brush (because of no more masking tape) .


Last edited by LeKid : 10 October 2017 at 02:53 PM.
 
  11 November 2017
Originally Posted by darthviper107: I just finished this 3D printing project, took a lot of time and trial and error but I'm glad it's finally done and I can go back to 3D stuff:
http://forums.cgsociety.org/showthr...f=358&t=1470445
Jesus this is good work.
__________________
LW FREE MODELS:FOR REAL Home Anatomy Thread
FXWARS
:Daily Sketch Forum:HCR Modeling
This message does not reflect the opinions of the US Government

 
  11 November 2017
Originally Posted by RobertoOrtiz: Jesus this is good work.
Thanks, I was really glad to have it done, originally tried to get it done much sooner but I really hate sanding, but forced myself to setup a schedule to finish it off.
__________________
The Z-Axis
 
  11 November 2017
Fan modeling and print of the Kashira from Spirited Away Ghibli.

I used a 0.25mm nozzle with a layer height of 100μm on UM2.
The print is about 68mm and took about 7h30 with an infill at 0%.

I printed this with the Silk Filament from Biofila by TwoBears.





I added a little color in zbrush for fun



Last edited by LeKid : 11 November 2017 at 08:26 AM.
 
  11 November 2017
Originally Posted by squidinc:er
It is such an amazing creature!!! I've never previously seen that before!!!Keep on!
 
reply share thread



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
CGSociety
Society of Digital Artists
www.cgsociety.org

Powered by vBulletin
Copyright ©2000 - 2006,
Jelsoft Enterprises Ltd.
Minimize Ads
Forum Jump
Miscellaneous

All times are GMT. The time now is 05:04 AM.


Powered by vBulletin
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.